Machinist Trade Question And Answer in Hindi Pdf 2021
Iti Machinist Trade की तैयारी कर रहे हैं. उन्हें काफी महत्वपूर्ण स्टडी मैटेरियल चाहिए होता है, ताकि आपकी तैयारी सही ढंग हो सके, इसलिए हमने Machinist Trade Question And Answer in Hindi Pdf 2021 प्रश्न उत्तर दिए हैं इन्हें आप ध्यान पूर्वक पढ़ें क्योंकि इसमें जो प्रश्न दिए गए हैं वह पिछले वर्षों परीक्षा में पूछे जा चुके हैं, और आगे आने वाली परीक्षाओं में पूछे जाने की पूरी पूरी संभावना है अगर आपको अन्य आईटी आई ट्रेड की तैयारी कर रहे हैं तो हमारी वेबसाइट पर प्रीवियस पे पर मिल जाएंगे
1.छोटे-छोटे कार्य को पकड़ने के लिए कौन सी वॉइस का प्रयोग किया जाता है?
उत्तर. हैंड वाइस
2.किस सरफेस पर प्लेट खरोच आने पर इस पर बर्र नहीं आते हैं?
उत्तर. ग्रेनाइट सरफेस प्लेट
3.रीमर कितने प्रकार के होते है?
उत्तर. हैंड रीमर, मशीन रीमर
4.ऐंगल प्लेट कोण मे बनी होती है?
उत्तर. 90°
5.पुल्लियो के बीच सेंटर से सेंटर दूरी बडी पुल्ली के व्यास का कितना गुना से कम नहीं होना चाहिए?
उत्तर. 3 गुना
6.किसी शाफ्ट पर श्रेडिंग करने से पहले उस पर करना चाहिए?
उत्तर. चेम्फर
7.खाँचे की चौड़ाई मापने के लिए प्रयोग करने के लिए कौन से कैलिपर का प्रयोग किया जाता है?
उत्तर. इन्साइड कैलिपर
8.किसी जॉब का केंद्र का निशान गहरा करने के लिए कौन से पंच का प्रयोग किया जाता है?
उत्तर. सेंटर पंच
9.कोल्ड चीजल का प्रयोग कहां किया जाता है?
उत्तर. फिटर शॉप
10.बाइस के स्पिन्डल पर चूड़ियां कटी जाती है
उत्तर. स्कवायर ग्रेड
11.बियरिंग के अन्दर तेल की नालियां काटने में प्रयोग कौन सी चीजल का प्रयोग किया जाता है?
उत्तर. हाफ राउंड नोज चीजल
12.कौन सी पुली एक सॉलिड पीस से बनाई जाती है इसमें दो तीन या अधिक स्टेप में होते हैं?
उत्तर. स्टेप पुली
13.चूड़ी कटे भाग कि वह चौड़ाई जो दो फ्लूट के बीच में होती है?
उत्तर. लैंड
14.किसका प्रयोग तार पीन घड़ियों के पुर्जे पकड़ने में किया जाता है?
उत्तर. पिन वाइस
15.फिलर गेज सेट में पाई जाती है?
उत्तर. 7
16.किस भाग के साथ डिस्क लगी होती है?
उत्तर. प्रोटेक्टर हेड
17.मशीन की शक्ति को एक स्थान से दूसरे स्थान पर पहुंचाने को कहते हैं?
उत्तर. पावर ट्रांसमिशन
18.कौन सी पुली पर अर्धवृत्तआकार गुव बना होता है जिसमें चैन या वायर रोप का प्रयोग होता है?
उत्तर. चैन या रोप पुली
19.स्लिप गेज कि दूसरी और तीसरी श्रेणी में कितनी स्लिप होती है?
उत्तर. 49
20.बेंच वाइस के जां एक दूसरे के खुलते हैं?
उत्तर. समान्तर
21.फास्टनर कितने प्रकार के होते हैं?
उत्तर. तीन प्रकार के
22.कटिंग ऐज के पीछे जो रिलीफ कोण होता है उसे क्या कहते हैं?
उत्तर. लिप क्लीयरेंस ऐंगल
23.किस का क्रॉस सेक्शन आयताकार होता है?
उत्तर. फ्लैट बेल्ट
24.चीजल किस मटेरियल का बना होता है?
उत्तर. हाई कार्बन स्टील
25.स्क्वेयर फाइल के चारों तरफ दाते बने होते है?
उत्तर. डबल कट
26.ट्राई स्क्वायर के कितने भाग होते हैं?
उत्तर. दो भाग स्टॉक, व ब्लेड
27.स्कु जैक में थ्रेड कटी होती है?
उत्तर. सोयर श्रेड
28.स्लिप गेज को सुरक्षा प्रदान करने के लिए प्रयोग किया जाता है?
उत्तर. प्रोटैक्टर स्लिप
29.जहां पावर को समान्तर शाफ्टो पर ट्रांसमिट करना होता है और दोनों शाफ्टो की चाल की दिशा एक दूसरे के पुली ड्राइव की अपेक्षा गियर ड्राइव अधिक उपयोगी होती है क्योंकि इसमें ——–होती है?
उत्तर. स्लिपेज की संभावना
30.प्रोट्रैक्टर का सिद्धांत किसके समान है?
उत्तर. वर्नियर बेवल प्रोट्रैक्टर
31.माइक्रोमीटर में रेचट स्टॉप सहायक होता है?
उत्तर. प्रेशर को कंट्रोल करने के लिए
32.सी क्लैम्प के स्कू और हैंडल प्राय कौन सी धातु?
उत्तर. माइल्ड स्टील
33.एडजेस्टेबल रैप गेज में एन्विल होते हैं?
उत्तर. 2 से 3
34.लम्बे शाफ्टो को सहारा देने के लिए स्थिर रखने के लिए कौन सी युक्ति का प्रयोग करेंगे?
उत्तर. बियरिंग
35.स्लाइडिंग और वर्किंग टेबल को ऊपर नीचे आगे पीछे करने के लिए प्रयोग किया जाता है?
उत्तर. रेक और
36.यह एक काल्पनिक डायामीटर होता है जो कि मेजर और माइनर डायामीटर के बीच में बना होता है उसे क्या कहते हैं?
उत्तर. पिच डायामीटर
37.मिट्रिक टेपर का शीर्ष कोण होता है?
उत्तर. 2°51’51”
38.वर्नियर बेवल प्रोट्रैक्टर लिस्ट काउंट कितनी होती है?
उत्तर. 5′
39.सरफेस गेज के आधार पर वी ग्रुव कटे होने का प्रयोजन कहां रखा जाता है?
उत्तर. जिससे इसे गोलाकार या वी आकार की सतह पर रखा जा सके
40.पंच द्वारा किए हुए सुराख को ड्रिफ्ट द्वारा बड़ा साइज में बनाने के लिए प्रयोग किया जाता है?
उत्तर. ड्रिफ्टिंग
41.ऑफसेट स्कु ड्राइवर का प्रयोग तंग या कोणीय स्थानों में इसके दोनों सिरे एक दूसरे के विपरीत ——के कोण पर मुड़े होते हैं?
उत्तर. 90 डिग्री
42.साधारण कार्यों के लिए कितने डिग्री का चीजल का कोण प्रयोग किया जाता है?
उत्तर. 60 डिग्री
43.मीट्रिक माइक्रोमीटर एक पूर्ण चक्कर में थिम्बल आगे बढ़ता है?
उत्तर. 0.50 mm
44.हेड फाइल चौड़ाई में पूरी लंबाई तक होती है?
उत्तर. समान्तर
45.बोल्ट का हेड कितने डिग्री पर चेम्फर होता है?
उत्तर. 30 से 35 डिग्री
46.गियर किस मेटल के बनाए जाते हैं?
उत्तर. कास्ट आयरन, माइल्ड स्टील, एलॉय स्टील, ब्रांज
47.उच्च कोर्ट को ट्रांसमिट करने के लिए प्रयोग की किया जाता है?
उत्तर. जिब हैड की
48.सेफ ऐज फाइल के ऐज पर दाते —— होते है?
उत्तर. नहीं
49.साधारण ड्रिल में कितने फ्लूट कटे होते हैं?
उत्तर. दो
50.कोल्ड सेट का प्रयोग इस कार्य के लिए किया जाता है?
उत्तर. छैनी को पकड़ने के लिए
Machinist Trade Question And Answer In English Pdf 2021
1. Different types of screws are used in the shaping machine as per the requirement. Which of the following is not included in these?
Answer. Inclined screws
2. On which of the following taps is the full length for the entire length?
Answer. Finisher tap
3. Which of the following procedures is followed to reduce stiffness and increase elasticity after the hardening process?
Answer. Naturalization
4. Where is the tool head in the shaper?
Answer. On ram face
5. Which of the following is not a method of lubrication?
Answer. Juice lubrication
6. Which of the following process is adopted to make the surface hard and the core flexible?
Answer. Surface hardening
7. From how many of the following, the angle of cold chisel changes?
Answer. 35 ° to 70 °
8. Which of the following screws (Vice) is used to hold round materials of small diameter?
Answer. Pin screws
9. Which of the following is a job keeping in a shaper?
Answer. At the speed of the table
10. Screw grade micrometer is used to measure which of the following?
Answer. pitch diameter
11. Which of the following is a combination set experiment?
Answer. Fitting Shop
12. Which of the following is not a function of spherical sand?
Answer. Make slot
13. Which of the following is the distance traveled by a feed drill of a drill?
Answer.On each round of Spidle
14. Which of the following types of sand is used in making keyways, slots, and grooves?
Answer. Columnar
15. In a shaper, which of the following parts can be adjusted up and down the table?
Answer. Cross rail
16. Which of the following is not a refrigerant job?
Answer. Stop electric shock
17 For which V block is used in a shaper?
Answer. Cylindrical surface
18. Which of the following does not include the mechanism used in Shaper?
Answer. Hydraulic
19. For soft materials, which of the following types of cuttings is preferred?
Answer. Rough
20. What is the function of a tap?
Answer. Internal shredding
21. Which of the following is not a function of a depth gauge?
Answer. Measuring the depth of blind holes
22. What is the minimum diameter of a grade?
Answer. Small diameter
23. In which of the following are the two legs of Tri Square?
Answer. Stock and blade
24. Which of the following is not one of the following types of slots used in the workshop?
Answer. Horizontal slotter
25. Which one of the following materials are not used in making hacksaw blades?
Answer. Aluminum
26. Which of the following types of drills is preferred for fast and correct work in a fitting shop?
Answer. Spasm drill
27. Which of the following is not a function of a cross pean hammer?
Answer. To rivet
28. What is the best cutting angle for a spiral drill?
Answer. 118 °
29. Which of the following ratios is commonly used in Shaper’s quick return motion mechanism?
Answer. 3: 2
30. By which of the following is the stroke length increased in the shaper?
Answer. Increasing the distance between the crankpin and the center of the bull gear
31. Which of the following is a tool used for shaping?
Answer. Multi-tip cutting tool
32. Which of the following does not fall under the concept of the 5S working environment of sustainable productivity in a company?
Answer. Contraction
33. Who responds to the following in a sizing machine.
Answer. RAM
34. What is the size of a tap?
Answer. The diameter of its bread
35. For which of the following tools is the neck like Goose used?
Answer. In very good finishing
36. What does a dial test measure represent?
Answer. Plunger lift
37. How do the bull gear, bank, and slotted liver mechanism rotate in the following?
Answer. In uniform angulation
38. The size of the shaper is determined by which of the following?
Answer. From maximum stroke length
39. In which direction does RAM move in a slotting machine?
Answer. Vertical direction
40. Which of the following processes makes the material soft?
Answer. Heating
41. The feed (S) in the shaper ……… .. is the relative motion of the double stroke towards the axis of work or tool ram’s reproduction.
Answer. Vertically
42. Which of the following is not a forging tool?
Answer. Reimer
43. In which of the following sizes is Steel Rule available?
Answer. 300 mm
44. Which of the following parts is used to lock the micrometer at the desired setting?
Answer. Spidle clamp
45. Which of the following tools is used for machining convex or concave grooves of V-shaped grooves or similar special shapes?
Answer. Form tool
46. What kind of blade is preferred for an unskilled or semi-skilled people?
Answer. Flexible blade
47. What is the accuracy of the external micrometer?
Answer. 0.01 mm
48. What is the following combination set?
Answer. CNon-efficiency measuring instrument
49. What is the work of anvil?
Answer. Support workpiece
50. Diamond chisel is used for
Answer. Making small holes square
ITI मशीनिस्ट ट्रेड परीक्षा में पूछे गए प्रश्न उत्तर
मशीनिस्ट ट्रेड परीक्षाओं की तैयारी करने वाले सभी उम्मीदवारों के लिए इस पोस्ट में machinist objective questions and answers pdf download, lathe machine questions and answers pdf in Hindi, machinist test questions, milling machine MCQ questions, and answers, CNC objective questions and answers pdf, machine tools objective questions pdf, Machinist Trade Question, lathe machine ke question,iti all trade question paper pdf, Machinist Trade Question उन्हें इस पेपर को ध्यान से देखना चाहिए .यह पेपर आपकी परीक्षा के लिए फ़ायदेमंद रहेगा.
Leave a Reply